Bialetti pressure valve

Bialetti pressure valve DEFAULT

Bialetti Brikka fix, repair and clean

חשוב! עדכוניםPlease note:
The use of dish washing soap / Vinegar / Citric acid is recommended only if you have a non functioning Brikka.
Regular cleaning of Brikka should be done with clean water only.

Check the gasket. If it is worn, too thin, dry or rotten, replace it.
Genuine replacement gasket can be obtained from Bialetti.
You can also use replacement gasket from a 3rd party.

For the Brikka 2 cups, original gasket size is:
Outer diameter OD = 66.7mm (2″ 5/8), Inner diameter ID = 50mm (2″)
Any standard 3 cup coffee pot gasket (with outer diameter OD of ~ 65mm, 2-1/2”) is OK

For the Brikka 4 cups, any standard 6 cup coffee pot gasket (with outer diameter OD of ~ 70mm, 2-3/4”) is OK

Clean the lower part of the coffee container, especially the area where it meets the filter’s flange and the thread.
If needed, clean the coffee pipe from this side as well (see D).

When done, rinse in water and dry all parts. Assemble the filter plate and gasket to its place. Pay attention that the flanged part of the filter plate is facing toward the coffee container.

Sours: https://www.schneordesign.com/diy/diy-coffee/bialetti-brikka-fix/

Troubleshooting Problems With a Bialetti Stovetop Espresso Coffee Maker

I've been an online writer for over seven years. My articles often focus on beauty, health tips, and cooking.

Maybe your moka pot is hissing and spitting steam or your coffee is too weak. Here are the ways to fix the most common problems with a Bialetti to make sure your morning brew is everything you expect.

Why is my Bialetti hissing and shooting a jet of steam out of the safety valve?

Three possible reasons: Either the safety valve is clogged, you’ve filled the reservoir above the fill line, or the filter may be clogged up so that the water isn’t escaping into the jug part of the pot as it should.

What to do: Take the whole pot apart, including the gasket and filter, and rinse thoroughly, wiping off any stray or stuck coffee grounds with a sponge. Also check to see if your safety valve has a tiny protuberance (like a little metal stick that you can push from the inside)—some of my older pots had this, but my newer one doesn’t. If so, push this in a few times (it springs back again) to dislodge the blockage. If the problem continues, you might have to send the pot back or buy a new one, depending on whether it’s still under warranty.

Why is only a trickle of coffee coming up into the top part of the pot?

Two possible reasons: Either the pot isn’t sealing properly (so that there’s not enough pressure to force the water through) or there’s a blockage in the filter or in the basket that holds the coffee grounds.

What to do: Again, take the pot apart completely, clean each part with hot water and a sponge, and check the filter and gasket and replace these parts if necessary.

Why is liquid hissing and spitting out where the top part screws into the bottom part?

Two solutions: Check that there are no stray coffee grounds in the grooves of the screw parts of the reservoir and pot that are preventing a tight fit when you screw them together. Alternatively, it might be time to replace the gasket.

Why does my coffee taste odd?

Two possible reasons: If you’ve cleaned the pot too enthusiastically, you might have scrubbed the ‘seasoning’ coating off, which can result in a metallic-tasting coffee. You'll have this same problem if the pot is brand new.

What to do: Season or re-season your pot by making a couple of pots using cheap coffee grounds and throwing the resulting coffee away.

Why does my coffee taste too weak?

What to do:

  • Try putting more grounds in the basket when you make the coffee (though if you fill the basket to about three-quarters full, this should be sufficient).
  • Make sure you’re only filling the reservoir up to the fill line—about a half a centimetre below the safety valve.
  • Use a dark roast coffee, which has a fuller, richer flavour.

Why are there black bits in my coffee?

  • If the bits are tiny, they are just a few stray coffee grounds that rise into the pot with the steam and hot water. A few tiny grounds is normal in any freshly-brewed coffee.
  • If there are lots or clumps of coffee grounds, replacing the pot's filter will help.
  • If the bits are large, flat pieces of solid coffee, these are flakes of built-up coffee from the inside of the pot. Give the inside of the pot a good hard wipe with a dish sponge, but don't scrub too hard, because you want to keep some of the natural coffee oils as seasoning so that your coffee doesn't taste metallic.

Why is coffee spilling out of the pot as it brews?

This means your coffee is boiling; turn down the heat when you put the pot on and this problem will go away.

Why is the Bialetti producing hot water only, no coffee?

You’ve likely forgotten to put coffee grounds in the basket!

It's been on the stove a long time but still, I see no coffee. . .

You’ve probably forgotten to put water in the reservoir. We shall say no more about it. Because we are classy.

Are You Using Your Bialetti Properly?

It's not hard to make a great cup of coffee with these machines, but there are specific things you must do, including seasoning it, loading it properly, and keeping it clean. Read How to Make Perfect Stovetop Espresso Coffee With a Bialetti Moka Pot to learn more.

© 2012 Redberry Sky

Comments

CMT on March 20, 2019:

Hi there,

I've got a new pot and I've tried many different temperatures but I can never get all of the water into the top pot. There is always water remaining in the bottom. Does anyone know why??

matthew D on March 04, 2019:

I have the same problem as Jeff.

Where can one buy a replacement air valve?? I have tried cleaning, boiling, scrubbing.....nothing works... I can find every replacement part but the air valve???

Thanks

[email protected] on October 05, 2018:

The Kitty will not warm up the coffe so thatt it is burning hot. Why?

Lina on March 25, 2018:

after i prepared the coffee, i cannot open it to clean it. What shall i do?

Cooper Robards on March 19, 2018:

Coffee is not emerging AT ALL into the upper chamber. I have a new gasket and filter and have a stainless steel GB pot, which hasn't been used that often. What's wrong?

john on February 27, 2018:

my pot doesn't whistle as it finishes

JillEH on February 04, 2018:

I think I do everything the same when I make a pot of espresso on the stove top, but sometimes I end up with some espresso (or brown water) in the bottom reservoir. What's happening?

Jeff on November 12, 2017:

Where can one buy a replacement air valve?? I have tried cleaning, boiling, scrubbing.....nothing works... I can find every replacement part but the air valve???

Thanks

Steve on January 23, 2017:

My pot doesn't seal right I have changed the gasket it still leaks steam it never makes a full pot please advise

ptmalloy on September 22, 2016:

I have a bialetti 6 moka. It has worked perfectly for year; this week I changed the metal filter and gasket (wi/a bialetti kit) and now it no longer works!

Rather than my delicious coffee smoothly surging out of the pipe, I get only steam, lots of steam. Eventually coffee will spurt out, but not much.

It does not seem to be leaking steam from the gasket area--no steam venting form the side, or coffee dribbling down. The coffee grounds are not compacted. So I think the pot is not generating enough pressure. But enough to put off a lot of steam.

One thing I have noticed, I cannot screw the two parts together as tightly with the new gasket.

This is making me very grumpy as I am missing my coffee!

Might you have any suggestions?

jb on September 09, 2016:

We have a vintage coffee maker and are unable to screw off the top from the bottom. We have tried everything. Any suggestions?

CathleenP on May 28, 2016:

Hi -- just wanted to confirm that if you're having the problem where the new gasket seems too small, meaning no real espresso, just a sputtering mess that starts to boil before the pot is even a third full, do check to see if there are dents in your funnel perimeter. The old gasket had molded to seal around the dents, but the new pristine gasket is not sealing around the dents. The solution is to replace the funnel.

Jim on April 19, 2016:

The Bialetti products do not have a good after-sales service. I was shocked to find that after the two-year warranty period, Bialetti will not repair customers' faulty units, or even supply the tiny replacement valve for a fee. I decided instead to purchase an alternative Italian-made pot from eBay. They are far cheaper and just the same quality.

Bill Bailey on March 30, 2016:

I just bought a standard Bialetti stove top coffee post. I put water and ground coffee in and placed on stove. All I got was hot water and the ground coffee (when the pot cooled enough to disassemble, seemed completely dry and untouched by the steam.

glamourbomb on December 27, 2015:

Correction: I had a damaged filter BASKET (not gasket) that was caused by trying to remove used grounds by tapping the basket on the side of the trash bucket causing it to become mis-shapen. A replacement filter basket resolved my problem.

glamourbomb on December 27, 2015:

For me, I discovered that the filter basket got mis-shapen when a vacationing visitor to my home tried to make me a cup of coffee. The moka pot wouldn't work after their visit. What happened was after waiting for the pot to boil, it would just gurgle but the upper chamber did not have coffee. Thinking it was the gasket/filer, I changed it but that didn't resolve the issue. It wasn't until I contacted Bialetti and was informed that a damaged filter gasket would account for a bad fitting seal. I bought a replacement on Amazon and it did the trick. So lesson learned: be careful when tapping out the used coffee grounds so as not to bend the filter. Instead, dig out the grounds with your finger and rinse.

Joseph on October 23, 2015:

I had the exact problem that Zafra experienced!

My seal after 5 year went bad. When I replaced the seal, the normal routine was no longer accepted by Mr. Bialetti! The Coffee would only come out 1/2 way and the venturi seemed to not be working. I cleaned all parts out numerous times, thinking perhaps that something was stuck or that that Mr Bialetti became to hot and never returned to his original shape.

However, after reading the advice from Redberry Sky, I think everything is back in order. I found out that I had been using too many grounds and tapping them down, and then I was using too much heat. I tried what Redberry Sky recommend 3/4 grounds and low heat. This seems to do the trick. I do think the coffee pot 'gets used' to its parts so after changing its parts, it needs to simply get used to them again. So, don't throw away Mr. Bialetti.... have patience and give him a chance. Millions of Italians can't be wrong!

monika on August 05, 2015:

Dave, I've had that happen if I've left the seal too long between changes (been using the same pot for almost 20 years) or overheated the pot - I get distracted so easily. Mine is a stainless steel pot, so I ended up using a stainless scourer to get the residue off, but if yours is an aluminum pot you might want to start with a nylon scourer instead.

Now, does anyone happen to know a supplier that stocks safety valves? I've got stream coming out of mine and a clean hasn't helped, so I'm thinking maybe the spring is worn or the ball bearing pitted or something. I believe they are a standard fit, but mine is an 8mm head in brass if that makes any difference.

DaveB on June 14, 2015:

Hi

I have had my stove top espresso maker (Bialetti 3 cup) for many years. i went to change the gasket but it has completely adhered to the inside rim. i scraped out what I could but there is still a thin layer of the rubber gasket clinging to the inside surface of the base. Any idea how this happened and how it can be removed?

Thanks

JaneyKay from Paris, France on April 12, 2015:

Just wanted to say thank you.

followed your advice and got it working again.

I think it was either the valve push trick or cleaning arouns the seal that made it work.

I'm rather disappointed though as my previous moka maker of unknown name worked perfectly for 4 years with no TLC at all.

Thanks again.

Steebke on October 19, 2014:

I had a good working one, need to replace the filter and rubber seal as it was falling apart. I do this every 4 years, I use it every day. But now, it didn't give me good coffee anymore. I found the problem, I removed the safety valve and cleaned it, now all is fine again, enjoying my coffee as we speak ;)

Redberry Sky (author) on January 31, 2014:

Hi Dave2002, I get the metallic taste thing with new pots - what I do is make two or three (or even four or five) pots using the cheapest ground coffee I can find (the fineness of grind doesn't matter for this - I throw the coffee i make with it down the sink!) - the coffee will coat the pot and the inside of the reservoir so that the metallic taste goes away. The longer and more often you use the moka pot, the better the coffee will taste (in my experience). When you make moka pot coffee for real (not just to coat the pot), an espresso grind gives a richer flavour; less fine grounds will be weaker. The slightly odd taste will go away after a few pots, it takes an hour or two's persistence :) Hope this helps :)

Dave2002 on January 31, 2014:

hello ,

My Bialetti is about 4 months old and I have never made a good cup of coffee. I'm just putting up with it until I found this website.

I use quality coffee and have tried 2 different grinds if coffee, espresso and a less fine grind.

When I purchased it I brewed 2 cups and threw them out. I've cleaned it with cold water and a sponge. I still have a metallic taste, not a rich flavor at all .

Super frustrated , help!!!!!

Velda on November 25, 2013:

Thanks so much. I will try this. And if that doesn't work out I hope I can return it. Well I should be able to return it.

Best

Redberry Sky (author) on November 24, 2013:

Hi Velda,

You might have been unlucky and got a faulty one - I'm not sure how long the guarantee is for the moka pots but you might be able to return it and get a replacement. But before you do, you could try taking removing the rubber seal and the filter plate it holds in place on the bottom of the 'pot' part (you can tease the rubber seal out gently using a sharp knife and the filter plate will come out easily then) and thoroughly rinsing everything separately in case there are some coffee grounds stuck somewhere and making the parts not fit together tightly enough. I suspect you have a faulty pot though - I get a few coffee grounds in my coffee, but for a lot to come through there would have to be a gap somewhere, and that shouldn't be happening if your moka pot is new.

Hope this helps

Velda on November 24, 2013:

Hi,

I'm getting a lot of grains in my coffee. The pot is quite new and I know how to use it. But I keep getting a lot of small grains in every cup. Can I do something to avoid this? It's a lot, not just a few.

Thanks

Redberry Sky (author) on October 23, 2013:

Hi curious, I've made half-pots in a moka pot, but it turns out much weaker. I have a six-cup size and you get less espresso than you think out of it (but I take my coffee very strong!). I've also used non-espresso ground coffee in my moka pot - it's kind of ok, but very weak - espresso grind is very tiny, filter grind is coarser, and using coarser grinds in a moka pot gives very weak coffee. A French Press might be better for you - you can make smaller amounts more easily without getting a weaker cup of coffee, or use the same pot to make a larger amount if you have friends over.

curious on October 08, 2013:

Hi, I am thinking to buy a Moka pot but I wonder what size should I buy. I only drink one cup at a time and therefore would only need a small pot but this would bring problems if I have quests over and I would have to make the coffee several times...so, it is possible to buy a e.g. a 4 cup pot and fill it only half full when I'm making coffee just for myself? (I don't like the idea of wasting delious and expensive coffee). Also can I use "normal" coffee grounds in Moka pot? I know it won't make espresso but can the Moka pot be used for making normal coffee as well?

Redberry Sky (author) on May 07, 2013:

Irishmazza – most interesting moka problem *ever*!

The only things I can think of is to soak it in water or cooking oil, and then try to 'pinch' it out with a pair of pliers – or, because it sounds like the inner basket might have become a little mis-shapen, try to stick the blade of a slim knife between the basket and the pot if you can find a little gap, and then lever it out.

BUT !!! One of the earlier commenters said that his moka pot had become a bit mis-shapen because he knocked it onto the side of his bin when he emptied it, and that made it stop working properly – which makes me think that if you do try the brute-force method to free up your stuck pot, it might damage it (which might not matter to you if the basket's irrevocably stuck).

Good luck – hope you manage to free it up and get your morning coffee. I have three bialettis, all the same size, that I've bought over the years – and when one dies, I mix-and-match the different pots, baskets and reservoirs until I get a combination that gives me a working coffee pot, so if you do end up buying a new one, it's worth keeping the old one for parts and buy the same size and model.

Nadia Archuleta from Denver, Colorado on April 02, 2013:

My sister had one of these -- it exploded its contents onto her stove about once a week. It was so complicated to get the measurements just right, and it still spewed regularly. She finally gave up and bought a machine. Too bad she hadn't seen your Hub first! Thanks for sharing.

Redberry Sky (author) on March 24, 2013:

Zafra - to me, it sounds like a pressure problem, but I don't know why it would only start after you changed the gasket. I've only had this problem when the valve on my moka pot has been faulty, or if the threads where the base screws into the top part have been clogged with coffee grounds. If your old seal (gasket) was perished, have you checked that there's no old rubber stuck to the pot that could be causing it to be not quite sealed? Having said all that, sometimes I can't find a reason why my own moka pots stop working - when I buy a new one I always try to get the same make and model so that the parts are interchangeable and I can mix and match them when the start to give me trouble. I hope you find the answer - I too hate to go without my morning coffee, so I empathise! :)

Zafra on March 19, 2013:

Here's a puzzle for you.

Hi there,

I have been using my moka pot - no idea what brand it is but it's quite old - for more than 4 years with the same gasket and the same everything. I put coffee and sometimes ground cinnamon in the basket, don't tamp, fill the bottom chamber with water past the escape valve (I know they always say not to do this but I've been doing it for years with no problems at all) and it comes out perfect every single time. Finally, the rubber gasket became so corroded that pieces of it started falling off and the pot started to leak a bit at the connection between the top and bottom chambers during brewing, although it was still producing a good pot of coffee. I went ahead and replaced the gasket with a brand new one which is the correct size. First pot came out perfect. Then suddenly it started brewing less than half a pot and the rest of the coffee stays in the bottom chamber boiling. Or sometimes nothing but steam comes up. I have taken the entire thing apart and cleaned every part, including pushing a pin through all the little holes in the filter plate that looked clogged. Still no luck. The only thing that has changed is the gasket. I've searched the internet and found no useful information. I'm at a complete loss and getting quite desperate because that daily coffee is, well, non-negotiable if you know what I mean. If you have ANY idea what could possibly be going on and what I might try to fix this problem I will be eternally grateful.

Redberry Sky (author) on February 15, 2013:

Eileen - Bialetti Moka Pots are made of Aluminium (U.S. Aluminum) and it's not possible for them to rust in any way. They do develop a coating of coffee on the inside, which is dark brown and can flake off and might look a little like rust - to prevent or cure this, wipe the inside with a dish sponge every week or two and the coffee coating will come off (mostly - but it sticks stibbornly in the metal creases, which is fine and is not harmful). If you wipe all the coffee coating off quite agressively, the next pot of coffee might taste a bit sour or bitter, so throw the first pot or two of coffee away after giving it a good scrub.

Eileen Goodall on February 15, 2013:

I had one of these and it kept going rusty, kept reseasoning it and still it would rust on the inside - threw it away eventually - very disappointed

Guy on January 19, 2013:

I had the same problem. I replaced the filter and rubber gasket. No change.

I had to also replace the funnel that holds the coffee. I used to tap the coffee out of it on the side of my waste bin. This alters the shape over time. The steams was escaping along the side of the funnel and past the gasket resulting in the bubbling sound and no coffee.

urbanangel on October 21, 2012:

thanks for the info...the last one cracked me up:)

Redberry Sky (author) on August 14, 2012:

Hi Emad, I’ve had this happen to me a few months ago. Try first taking the whole pot apart – including removing the metal ‘sieve’ and rubber gasket on the underside of the main pot where the coffee bubbles up into, and wash everything separately in warm soapy water, rinse it all off and see if that works (it could be coffee grounds stuck somewhere and clogging the pot up). If that doesn’t work, it could be that the rubber gasket isn’t forming a seal properly between the top coffee pot and the bottom water reservoir – you can get a pack of replacement seals quite cheaply off Amazon, and that often works because the rubber seals only last for about 3-4 months before they get too frayed. The only other thing I can think of (and this happened to me) is that the pressure valve on the side of the bottom water reservoir is clogged or broken – I could find nothing at all that could help with this (some of them are on a spring and you can push it in and out a few times from the inside to try to clear it) and I think the inside mechanism was just bust – I don’t think the safety valve can be replaced and I had to buy a new moka pot, but try everything else first (dismantle the whole thing and clean any stray grounds off, and replace the seals and possibly the little ‘sieve’ plate – you can buy these and the rubber gaskets in packs together). Two more things are to make sure you don’t pack the coffee grounds in when you make a pot – if they’re packed down tightly they won’t let the steam get through to bubble up; and also don’t fill the reservoir up too much with water, it should be below the safety valve on the inside of the bottom chamber of the pot. Sorry for the very long reply, I’m trying to think of anything you can try that might work! Good luck, hope one of these helps – it’s hugely frustrating not to be able to get your morning coffee :)

Emad on August 14, 2012:

My pot is steaming, so there is steam jetting through but zero to minimal coffee enters the pot, and there is no hissing bubbling sound. Plz help!

Sours: https://delishably.com
  1. Black closet ideas
  2. Scythe factions ranked
  3. Bats pitch spec

Bialetti Mukka Express Replacement Pressure Valve, Fits Mukka 1-2 Cup

Bialetti Mukka Express Replacement Pressure Valve, Fits Mukka 1-2 Cup

Bialetti

200 ratings Write a review

Item #:

VND968184

Order now and get it around Tuesday, October 26

Note: Electronic products sold in US store operate on (110-120) volts, a step-down power converter is required for the smooth device function. It is mandatory to know the wattage of the device in order to choose the appropriate power converter. Recommended power converters Buy Now.


Product Details

  • New mixing valve for lots more flavour Blister Packs
  • International products have separate terms, are sold from abroad and may differ from local products, including fit, age ratings, and language of product, labeling or instructions.
Product Dimensions1.97 x 1.97 x 1.57 inches (5 x 5 x 4 cm)
Item Weight3.52 ounces (99.79 grams)
ManufacturerBialetti
ASINB01N5THPUG
Item model number8006363011099
MaterialAluminum
BrandBialetti
ColorBlack
Item Weight0.1 Kilograms
Item Dimensions LxWxH1.97 x 1.97 x 1.57 inches (5 x 5 x 4 cm)

Description

Product Description

Replacement valve for 1 or 2 cup Mukka Express or Mukka Express Elettrica. New mixing valve for lots more flavour. Blister pack. Easy to replace - instructions on rear of packaging.

Set Contains:

Valve

Similar Products

Stovetop cappuccino maker

Customer Questions & Answers

  • Question: Can you add/use this valve on a regular moka pot?

    Answer: No, this is for the Mukka Express pot only as stated in the product listing. The regular moka pots use a smaller valve that is Bialetti does not intend to be replaceable.
  • Question: This valve replacement fix for 5-6 cup mukka express cappuccino maker?

    Answer: No, it only fits the models specified in the listing.
  • Question: If it's not genuine who makes the aftermarket valve?

    Answer: This is a Bialetti replacement valve.
  • Question: My pressure valve blew up after 4 years of use. Is it better to purchase this valve or a brand new Mukka express pot ?

    Answer: New pots are hard to find, they were originally $89 if you can find one sometimes people price gouge and I have seen them as high as $300 I think this is crazy. Check eBay I have seen a couple new for About 100. Valve is ok at $45 pots rarely have anything wrong with them.
  • Question: Understand there are 2 versions in the market. how do i know which version is mine? i bought my mukka last year. mine dun have red rubber ring.

    Answer: i believe there is only one replacement valve so should work on either version.

Customer Ratings

23 customers ratings

  • 5 Star 80%
  • 4 Star 5%
  • 3 Star 8%
  • 2 Star 3%
  • 1 Star 4%

Review this product

Share your thoughts with other customers

Customer Reviews

Ca•• ••on

April 21, 2021

Great coffee maker. Worth the expensive parts

The new valve it's slightly different than te old one; More square looking and with a gre piece in between valve and stem.

Ca•• ••ol

April 10, 2021

Doesn't work like original valve.

It is not the original valve that came with the Mukka Express and consequently does not perform as well. It does not froth the milk.

VU•• ••LO

March 30, 2021

Excelente compra

La válvula llegó antes de la fecha compromiso a mi domicilio; es un artículo o repuesto que antes me constaba mucho trabajo conseguir para mi cafetera Bialetti.

Re•• ••on

December 29, 2020

Lifetime of previous one(bought from Bialetti oulet) was 10 months. I'll update when this one break.

It fits well.

Go•• ••d

December 16, 2020

Good when it worked (for two weeks)

The seal ended up busting after two weeks. It seamed like it wasn't the correct one. It broke right in half. I love my Mukka Express but unfortunately, I would not buy this valve again.

B •• ••

July 20, 2020

Fit the cappuccino pot we had

The way it fits on the pot

Ir•• ••na

April 25, 2020

Perfect replacement.

Perfect replacement. Got it quickly and works great!

To•• ••m

March 30, 2020

Am•• ••er

December 23, 2019

Happy Day

Very pleased. Was a bit sceptical at first on whether it was going to work or not because the item that I bought this piece for is either extremely difficult to achieve or nonexistent due to the date of when it was manufactured. Again, very happy. Thanks

Fa•• ••K.

September 9, 2017

Two Stars

Stopped working

Load More Reviews

Write Your Own Reviews

Only registered users can write reviews. Please log in or register

Sours: https://www.ubuy.vn/en/product/1WT23QI-bialetti-8006363011099-valve
8 Common Reasons Causing Your Moka Pot To Stop Working Normally

Bialetti Mukka Express Replacement Pressure Valve

Bialetti Mukka Express Replacement Pressure Valve

Bialetti

200 ratings Write a review

Item #:

IDR580475

Order now and get it around Tuesday, October 26

Note: Electronic products sold in US store operate on (110-120) volts, a step-down power converter is required for the smooth device function. It is mandatory to know the wattage of the device in order to choose the appropriate power converter. Recommended power converters Buy Now.


Product Details

  • Top Replacement Valve for Bialetti Mukka Express
  • Bialetti Original Replacement Part
  • Fits: Mukka Express 1-2 Cup (Stovetop Model)
  • Fits: Mukka Express 1-2 Cup (with Electric Base)
Product Dimensions1.18 x 1.18 x 1.97 inches (3 x 3 x 5 cm)
Item Weight3.52 ounces (99.79 grams)
ManufacturerBialetti
ASINB002KNSB92
Item model number109405
BrandBialetti
Capacity2 Cups
Item Weight0.1 Kilograms
Item Dimensions LxWxH1.18 x 1.18 x 1.97 inches (3 x 3 x 5 cm)

Description

It is the valve staid in the superior part of the coffeepot and uses in ordet to distribute two levels of pressure. It has to be cleaned up periodically and its eventual substitution is very simple. Fit only for the coffeepots for cappuccino: Mukka express 1 cup, electric Mukka 2 cups, Mukka express 2 cups.

Similar Products

Bialetti replacement parts

Customer Questions & Answers

  • Question: Cannot replace valve using o ring that came with the new valve.The valve will not seat properly on o ring .New o ring is clear color??

    Answer: I’m not sure what is wrong, I have not had trouble with replacing them. Perhaps there is a YouTube video to show you how, perhaps it is defective. Or perhaps you are putting it in the wrong place. Not sur
  • Question: Can this valve be used in other esspresso makers brands

    Answer: I do not think so. I think Bialetti has a proprietary design unique to their own Mukka Express makers. Curious why you want to use one elsewhere? If you have a new Mukka valve, I will buy it from you.
  • Question: Is this item authentic? And does it come on its original package shown in the picture.

    Answer: In my experience, the item is authentic....but a bit expensive.... a good working pressure valve is necessary for the espresso stove top to work correctly....
  • Question: how do I install the gasket? The directions aren't english.

    Answer: Just pull the gasket down onto the top of the center where the valve is to be placed ....it will seat itself when you do this....then you are ready to go.....
  • Question: Is this for the 2 cup size?

    Answer: Yes. I broke the original pressure valve for the Mukka Express Bialetti 6990 cappucino maker which is the 2-cup model. I bought this replacement and it works just fine for it.
  • Question: The valve on my old mukka express has finally broken and needs to be replaced. is this valve compatible with the older mukka express model?

    Answer: NO, it doesn't work as well as the valve that came with original pot. It doesn't frost the milk as well as the original. Needless to say, I wasted my money on the new valve. I have not used my Mukka express since.
  • Question: How do I install this little red ring that came with it?

    Answer: Work it into the groove just below the top of the stem that extends up the center of the milk container. If the red o-ring is not installed the steam escapes through side of the 'cappuccino' valve, rather than down into the part of the valve that froths the milk.

Customer Ratings

116 customers ratings

  • 5 Star 62%
  • 4 Star 9%
  • 3 Star 5%
  • 2 Star 5%
  • 1 Star 19%

Review this product

Share your thoughts with other customers

Customer Reviews

Sh•• ••ka

October 3, 2021

Excellent item!

My husband use it everyday and helps him make a great cup of cappuchino! It was shipped quickly and arrived in excellent condition, thank you!

fr•• ••il

September 17, 2021

this broke within 5 months!

My original part lasted years, and this one in 5 months broke while in use and sprayed coffee all over my ceiling, stove and floor, thank goodness I was in the other room and not standing by it!!

Am•• ••er

August 18, 2021

Great replacement

Exact replacement

Ju•• ••ro

August 7, 2021

Valve does not work

Valve is not working right... Seems like I lost my money.

Wi•• ••l

June 29, 2021

The replacement pressure valve did not work properly. I struggled to remove it on the first use.

The replacement pressure valve did not fit properly. It was a bad investment and I would not recommend it as a replacement pressure valve. Very disappointed with the replacement pressure valve.

Ca•• ••er

June 3, 2019

Lasted only two months

I love my Bialetti Mukka and was happy to find the replacement valve. Unfortunately, it broke one week after the product support eligibility expired. I am trying to find out how the seller might handle this.

Ja•• ••ls

February 27, 2019

Works like a charm

Now I'm back to using my Bialetti Mukka Express again! It works better than the original.

re•• ••el

February 13, 2019

Product as advertised

These valves used to sell for $10 so today's price is hard to swallow. But we love our morning Cappuchino from our Mukka Express and Bialetti stopped selling valves several years ago. Valves are very difficult to find so grab one of these if you want to extend the life of your Mukka Express.

an•• ••to

April 4, 2018

Load More Reviews

Write Your Own Reviews

Only registered users can write reviews. Please log in or register

Sours: https://www.ubuy.co.id/en/product/QO2BJOW-bialetti-mukka-express-replacement-pressure-valve

Valve bialetti pressure

Bialetti Mukka Express Replacement Pressure Valve, Fits Mukka 1-2 Cup

Bialetti Mukka Express Replacement Pressure Valve, Fits Mukka 1-2 Cup

Bialetti

200 ratings Write a review

Item #:

IDR625286

Order now and get it around Tuesday, October 26

Note: Electronic products sold in US store operate on (110-120) volts, a step-down power converter is required for the smooth device function. It is mandatory to know the wattage of the device in order to choose the appropriate power converter. Recommended power converters Buy Now.


Product Details

  • New mixing valve for lots more flavour Blister Packs
  • International products have separate terms, are sold from abroad and may differ from local products, including fit, age ratings, and language of product, labeling or instructions.
Product Dimensions1.97 x 1.97 x 1.57 inches (5 x 5 x 4 cm)
Item Weight3.52 ounces (99.79 grams)
ManufacturerBialetti
ASINB01N5THPUG
Item model number8006363011099
MaterialAluminum
BrandBialetti
ColorBlack
Item Weight0.1 Kilograms
Item Dimensions LxWxH1.97 x 1.97 x 1.57 inches (5 x 5 x 4 cm)

Description

Product Description

Replacement valve for 1 or 2 cup Mukka Express or Mukka Express Elettrica. New mixing valve for lots more flavour. Blister pack. Easy to replace - instructions on rear of packaging.

Set Contains:

Valve

Similar Products

Stovetop cappuccino maker

Customer Questions & Answers

  • Question: Can you add/use this valve on a regular moka pot?

    Answer: No, this is for the Mukka Express pot only as stated in the product listing. The regular moka pots use a smaller valve that is Bialetti does not intend to be replaceable.
  • Question: This valve replacement fix for 5-6 cup mukka express cappuccino maker?

    Answer: No, it only fits the models specified in the listing.
  • Question: If it's not genuine who makes the aftermarket valve?

    Answer: This is a Bialetti replacement valve.
  • Question: My pressure valve blew up after 4 years of use. Is it better to purchase this valve or a brand new Mukka express pot ?

    Answer: New pots are hard to find, they were originally $89 if you can find one sometimes people price gouge and I have seen them as high as $300 I think this is crazy. Check eBay I have seen a couple new for About 100. Valve is ok at $45 pots rarely have anything wrong with them.
  • Question: Understand there are 2 versions in the market. how do i know which version is mine? i bought my mukka last year. mine dun have red rubber ring.

    Answer: i believe there is only one replacement valve so should work on either version.

Customer Ratings

23 customers ratings

  • 5 Star 80%
  • 4 Star 5%
  • 3 Star 8%
  • 2 Star 3%
  • 1 Star 4%

Review this product

Share your thoughts with other customers

Customer Reviews

Ca•• ••on

April 21, 2021

Great coffee maker. Worth the expensive parts

The new valve it's slightly different than te old one; More square looking and with a gre piece in between valve and stem.

Ca•• ••ol

April 10, 2021

Doesn't work like original valve.

It is not the original valve that came with the Mukka Express and consequently does not perform as well. It does not froth the milk.

VU•• ••LO

March 30, 2021

Excelente compra

La válvula llegó antes de la fecha compromiso a mi domicilio; es un artículo o repuesto que antes me constaba mucho trabajo conseguir para mi cafetera Bialetti.

Re•• ••on

December 29, 2020

Lifetime of previous one(bought from Bialetti oulet) was 10 months. I'll update when this one break.

It fits well.

Go•• ••d

December 16, 2020

Good when it worked (for two weeks)

The seal ended up busting after two weeks. It seamed like it wasn't the correct one. It broke right in half. I love my Mukka Express but unfortunately, I would not buy this valve again.

B •• ••

July 20, 2020

Fit the cappuccino pot we had

The way it fits on the pot

Ir•• ••na

April 25, 2020

Perfect replacement.

Perfect replacement. Got it quickly and works great!

To•• ••m

March 30, 2020

Am•• ••er

December 23, 2019

Happy Day

Very pleased. Was a bit sceptical at first on whether it was going to work or not because the item that I bought this piece for is either extremely difficult to achieve or nonexistent due to the date of when it was manufactured. Again, very happy. Thanks

Fa•• ••K.

September 9, 2017

Two Stars

Stopped working

Load More Reviews

Write Your Own Reviews

Only registered users can write reviews. Please log in or register

Sours: https://www.ubuy.co.id/en/product/1WT23QI-bialetti-8006363011099-valve
How to Use the Bialetti Moka Pot Express for Espresso

I started to lift up my skirt and got into my panties. I began to drive my finger across the clitoris, my pussy at that time was already wet. Then she began to caress her breasts too.

Now discussing:

The brother himself lay leaning back, catching a. Buzz. Katya involuntarily bulged her eyes. With a distant gaze, he caught what was happening in the background, hearing, immersed in the fog, registered laughter.



1226 1227 1228 1229 1230