2015 prius oil

2015 prius oil DEFAULT

Toyota Prius Engine Oil Change Guide
How to change the motor oil and replace the cartridge filter in a 3rd generation Toyota Prius L I4 hybrid.

''13 Prius L Engine
Twist Off Oil Filler Cap
Oil Filler Cap Removed
This automotive "how-to" guide was specifically written to assist owners of the third generation (, , , , & ) Toyota Prius with the 2ZR-FXE L inline four cylinder engine in changing the motor oil and replacing the cartridge oil filter.

Owners of other vehicles equipped with the 2ZR-FXE L L4 Atkinson cycle engine such as the Lexus CTh, and Toyota Auris Hybrid or the previous "Gen II" Prius with the similar L 1NZ-FXE engine may also find these DIY oil change instructions to be helpful.

The tools needed to complete this procedure include a floor jack, jack stands, a small flathead screwdriver, a 14mm socket with a 3/8" drive ratchet or a 14mm wrench, a 64mm oil filter wrench with 14 flats such as the AST Tools TOY , a 24mm or 15/16" socket with 1/2" drive ratchet, a used oil catch container, an automotive funnel, a new cartridge oil filter, and 5 U.S. quarts of SAE 0W oil.

A few compatible cartridge style oil filters include the following with their part numbers: Mobil 1 M1C, Wix , Fram CH or TG, Pennzoil HPZ, Hastings LF, Toyota YZZA6 and Pentius PCBToyota-Prius-Engine-Oil-Change-Filter-Replacement-Guide
Pull Up Oil Dipstick
Raise Front of Vehicle
Service Access Panel
The first few steps are to warm up the motor to operating temperature, park the vehicle on a level surface, and turn off the engine.

Warming up the engine helps suspend any contaminants within the old oil and allow it to drain out more quickly.

Then engage the emergency parking brake and chock the rear wheels to prevent the vehicle from moving.

Open the hood, twist off the oil filler cap in the counter clockwise direction, and lift up the yellow handled oil dipstick.

Removing the oil filler cap and pulling out the dipstick prevent a vacuum from forming and allow the old oil to drain more quickly.

Next raise the front passenger side of the vehicle with the floor jack and securely support it with two jack stands.

Pry Out Center of Rivet
Pull Out Outer Piece
Removing Fastener
Slide underneath the front passenger area and locate the rectangular access panel in the black plastic engine under cover marked with the words "For Service".

There are three black plastic fasteners that hold the service panel in place.

Pry out the small circular inner piece first and then pry out the larger outer piece to remove the fastener.

Remove 3rd Fastener
3 Fasteners Removed
Open Service Panel
Once all three of the black plastic fasteners have been removed, you can flip open the service panel.Toyota-Prius-Engine-Oil-Change-Filter-Replacement-Guide
Remove 14mm Drain Bolt
Draining Old Oil Out
Replace Drain Bolt
The silver metal oil drain bolt is located at the bottom of the black metal oil pan facing towards the rear of the vehicle.

Move the used oil catch container to directly below the oil drain bolt.

Remove the oil drain bolt with the 14mm socket and ratcheting wrench by turning it counter clockwise.

If the drain bolt is equipped with a crush washer, inspect it and replace it if necessary.

It is an "M12" sized washer that can be purchased at your Toyota dealership's parts counter or at most auto parts stores.

The washer or "gasket" part number is Toyota .

Be careful when you remove the oil drain bolt since the old oil may be hot enough to cause burns depending on how long you allowed the engine to warm up in the first step.

Allow the old oil to drain out for a few minutes, re-insert the oil drain bolt in the clockwise direction, and tighten it to just past hand tight or about 28 ft lbs of torque. It would be best to replace the old crush washer on the drain bolt with a new one.

24mm Socket & TOY
New Cartridge Oil Filter
Oil Filter Cap
The round black plastic oil filter cap is located just behind the oil pan closer to the passenger (right) side of the vehicle. The oil filter cap faces towards the driver side of the car.

To remove the oil filter cap, you'll need a 64mm oil filter wrench with 14 flats (or "flutes") such as the Assenmacher Tools TOY , Toyota SST (Special Service Tool) # , or #


Attach Oil Filter Wrench
Loosen With 24mm Socket
Move Used Oil Basin
Slide the used oil catch container to directly underneath the oil filter cap. Place newspapers below the basin to keep your garage floor clean.

Push the 64mm oil filter wrench on to the filter cap, attach the 24mm or 15/16" socket with ratcheting wrench, and slowly turn it counter clockwise until the filter cap can be removed. (You may need to push the silver metal tab away from the filter cap to allow it to start turning.)

The old cartridge oil filter may fall out when you remove the cap. Be sure to remove the old rubber o-ring at the base of the threads on the oil filter cap.

Cartridge Filter & O-Ring
Tighten Oil Filter Cap
Replace Service Panel
Allow the old oil to drain from the oil filter receptacle for a few minutes.

I recommend buying the genuine OEM Toyota YZZA6oil filters since they have excellent reviews on Amazon.

Lubricate the new rubber o-ring with some fresh 0W oil and install it on to the base of the threads on the filter cap.

Insert the new cartridge oil filter into the oil filter cap and thread it on by hand a few turns in the clockwise direction to prevent it from becoming cross threaded.

Re-attach the 64mm oil filter wrench and slowly turn it clockwise with the 24mm socket to tighten the oil filter cap to just past hand tight or about 18 ft lbs of torque.

Do not over tighten the oil filter cap to avoid damaging the rubber o-ring which may cause oil leaks.

Insert Fastener Outer Piece
Push In Center Piece
Replace 2nd Fastener
Double check that the oil drain bolt and oil filter cap are tight before continuing on to the next steps.

Replace the black plastic service panel and line up the three holes in the panel with the corresponding holes in the engine under cover.

Re-insert the three round black plastic retaining clips by first pushing in the larger outer section and then popping in the smaller inner piece.

Replace 3rd Fastener
Insert Automotive Funnel
Pour In New 0W Oil
Lower the vehicle from the jack stands and the floor jack.

Move to the engine bay and insert an automotive funnel into the oil filler hole.

Pour in four quarts of new SAE 0W oil into the funnel. The engine's total oil capacity for an oil change with filter replacement is US quarts ( L or Imperial quarts).

It is far easier to add more oil into the engine than to drain some from an over filled engine. You may also not need to pour in the entire U.S. quarts depending on how long you allowed the old oil to drain out.

Pull Out Engine Oil Dipstick
Check Oil Level
Replace Oil Filler Cap
Temporarily replace the oil filler cap, run the engine for a few minutes, turn it off, and allow the oil to drain down to the oil pan for a few minutes.

Pull out the yellow handled oil level dipstick located near the front left corner of the engine cover.

Slowly add in more oil and repeatedly re-check the dipstick until the level is at or near the upper dot indicating that the engine is "Full".

If you haven't already, replace the dipstick and twist on the oil filler cap.

Be sure to check the oil level on the dipstick several times over the next week and watch your driveway for oil spots that may indicate a leak from the oil drain bolt or filter cap. Record the mileage and oil change details in your service record book.

To reset the "Oil Maintenance" reminder message, first turn the car "On". Then set the odometer to "Trip A" and turn the car "Off" by pressing the "Power" button. The last step is to press and hold the "MPH km/h" button before pressing the "Power" button to turn on the car. Keep holding the MPH button until the multi-information display shows that the reset is complete.

For more, check out my other Toyota Prius DIY Repair & Maintenance Guides.

Sours: https://www.paulstravelpictures.com/Toyota-Prius-Engine-Oil-Change-Filter-Replacement-Guide/


Toyota Prius Oil Maintenance Required Reset

Automotive, Daily Oil Light Reset Tip

 Toyota Prius

Toyota Prius

To reset the Toyota Prius, please follow these instructions:


1. Press the "ENGINE START STOP" switch once (do not start engine) or turn ignition key to run (one position before starting engine).
2. Ensure Trip Metre A reading is shown. Turn the ignition off.
3. While holding the MPH or KM/H button turn the ignition on (do not start engine).
4. Continue to press and hold the button until the trip meter displays "" and the display indicates the reset is complete.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.


TRIP & MPH Button Location

TRIP & MPH Button Location

Sours: https://oilreset.com/toyota-prius-oil-maintenance-required-reset/
  1. Werewolf online roles
  2. Kit de sutura
  3. Merrill lynch ct

Oil Change Light Reset Toyota Prius

The Oil Change Light Reset Toyota Prius will need to be performed after every oil change. If it is not reset the system will be unable to properly track when your next oil change is due.

Below is the procedure for the Toyota Prius . Follow the steps below to reset the oil life monitor after each oil change.

Oil Change Light ResetToyota Prius .

Oil Change Light Reset Toyota Prius Procedure

  1. Press the “ENGINE START STOP” button once or turn the ignition key to “RUN” position.
  2. Make sure trip meter “A” is displayed and turn the ignition off.
  3. While holding the trip meter reset button, press the “ENGINE START STOP” button once or turn the ignition key to “RUN” position.
  4. Continue to hold the button until “” is displayed.
  5. Turn the ignition off.

Oil Viscosity and Capacity

The liter engine holds approximately quarts ( liters) of 0W oil when the engine oil and filter are changed.

The liter engine holds approximately quarts ( liters) of 0W oil when the engine oil and filter are changed.

Not Working?

If the oil change light reset procedure is not working to reset your oil life monitor, make sure you are following each of the steps exactly and in the order displayed in the Oil Change Light Reset Oil Change Light Reset Toyota Prius procedure above. If this is not the oil life monitor reset procedure for your vehicle, restart your oil light reset procedure search HERE

Oil Life Monitor Reset Procedure Frequently Asked Questions

If you are still having trouble with visit the Oil Life Monitor Reset Procedure Frequently Asked Questions (FAQ) page for more information.


Due to the wide range of vehicles makes and models, this is general information and should not be taken as specific to any vehicle. Please consult the vehicle manufacturer for the correct specifications and repair procedures for your vehicle. This information is meant to be used as a guideline only.

Sours: https://resetoillight.com/toyota/oil-change-light-reset-toyota-prius/
HOW TO: Reset MAINTENANCE REQUIRED light on 2015 Toyota Prius

They preferred not foreign students, but Native Americans. Dan was also unlucky to pick up a drunk slut: there was no extra money, and also, when drunk, he even remembered his face. Disfigured by boils.

Prius oil 2015

It hurt a little at first, but then nothing. Thus, my already former friends, cleared my ass. My virgin ass took on fifteen cocks in a row. They came right inside me.

▶️HOW TO - Prius Oil Change, 2010-2015 Step-by-Step Directions ( COMPLETE GUIDE)

Up to him, and then she sat down and started slowly to clean the guy's penis, from his own sperm, which she easily swallowed. The organ even twitched a couple of times, forcing her to stand up slightly. So, - Yana kissed the head of the organ, deliberately touching the urethra with the very tip of her tongue. Thank you, honey. Our stop, huh.

Now discussing:

I took off her stockings and began to kneel and caress her legs. I did not notice where the whip appeared in her hands. She hit me on the back. It was very painful.

690 691 692 693 694